PMIC
介绍PMIC的功能和使用方法。
目前我司支持的 P1 PMIC 芯片，他们在 SPL/UBOOT/KERNEL 阶段都有相应的控制接口。
SPL/UBOOT 使用方法
uboot-2022.10$ vi arch/riscv/dts/k1-x_spm8821.dtsi
&i2c8 {
clock-frequency = <100000>;
u-boot,dm-spl;
status = "okay";
spm8821: pmic@41 {
compatible = "spacemit,spm8821";
reg = <0x41>;
bus = <8>;
u-boot,dm-spl;
regulators {
/* buck */
dcdc_6: DCDC_REG1 {
regulator-name = "dcdc1";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
regulator-init-microvolt = <950000>;
regulator-boot-on;
u-boot,dm-spl;
regulator-state-mem {
regulator-off-in-suspend;
};
};
dcdc_7: DCDC_REG2 {
regulator-name = "dcdc2";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
};
dcdc_8: DCDC_REG3 {
regulator-name = "dcdc3";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
regulator-boot-on;
u-boot,dm-spl;
};
dcdc_9: DCDC_REG4 {
regulator-name = "dcdc4";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
};
dcdc_10: DCDC_REG5 {
regulator-name = "dcdc5";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
};
dcdc_11: DCDC_REG6 {
regulator-name = "dcdc6";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
};
/* aldo */
ldo_23: LDO_REG1 {
regulator-name = "ldo1";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
regulator-init-microvolt = <3300000>;
regulator-boot-on;
u-boot,dm-spl;
};
ldo_24: LDO_REG2 {
regulator-name = "ldo2";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_25: LDO_REG3 {
regulator-name = "ldo3";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_26: LDO_REG4 {
regulator-name = "ldo4";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
/* dldo */
ldo_27: LDO_REG5 {
regulator-name = "ldo5";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_28: LDO_REG6 {
regulator-name = "ldo6";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_29: LDO_REG7 {
regulator-name = "ldo7";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_30: LDO_REG8 {
regulator-name = "ldo8";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_31: LDO_REG9 {
regulator-name = "ldo9";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_32: LDO_REG10 {
regulator-name = "ldo10";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_33: LDO_REG11 {
regulator-name = "ldo11";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
sw_2: SWITCH_REG1 {
regulator-name = "switch1";
};
};
};
};
SPL 阶段电源开启及电压设置方法
dcdc_6: DCDC_REG1 {
regulator-name = "dcdc1";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
regulator-init-microvolt = <950000>; ---> 加上该字段，会自动设置该电源电压为0.95v
regulator-boot-on; ---> 加上该字段，在SPL阶段会自动打开该电源
u-boot,dm-spl; ---> 需要加该字段，SPL才可识别该dts node
regulator-state-mem {
regulator-off-in-suspend;
};
};
UBOOT 阶段电源开启及电压设置方法
uboot 阶段有两种方式设置或者开启电源，第一种是直 接在 dts 中配置
dcdc_6: DCDC_REG1 { --> regulator_get_by_devname传入的名字参数
regulator-name = "dcdc1";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
regulator-init-microvolt = <950000>; ---> 加上该字段，会自动设置该电源电压为0.95v
regulator-boot-on; ---> 加上该字段，在UBOOT阶段会自动打开该电源
regulator-state-mem {
regulator-off-in-suspend;
};
};
另外一种是直接在代码中设置：
1. 首先要获得想要设置或者开启电压的regulator句柄
struct udevice *rdev = NULL;
char *regulator_name = "DCDC_REG1" --> 该字段传入的是dts中标识的dts node的名字
ret = regulator_get_by_devname(regulator_name, &rdev);
2. 开启某一路电
regulator_set_enable(&rdev, true);
3. 设置某一路电的电压
regulator_set_value(&rdev, 1800000);
Linux kernel 使用方法
Linux 内核中相关的 dts 配置分别为：
&i2c8 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c8>;
status = "okay";
spm8821@41 {
compatible = "spacemit,spm8821";
reg = <0x41>;
interrupt-parent = <&intc>;
interrupts = <64>;
status = "okay";
vcc_sys-supply = <&vcc4v0_baseboard>;
dcdc5-supply = <&dcdc_5>;
regulators {
compatible = "pmic,regulator,spm8821";
/* buck */
dcdc_1: DCDC_REG1 {
regulator-name = "dcdc1";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
regulator-always-on;
};
dcdc_2: DCDC_REG2 {
regulator-name = "dcdc2";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
regulator-always-on;
};
dcdc_3: DCDC_REG3 {
regulator-name = "dcdc3";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
dcdc_4: DCDC_REG4 {
regulator-name = "dcdc4";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
dcdc_5: DCDC_REG5 {
regulator-name = "dcdc5";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
regulator-always-on;
};
dcdc_6: DCDC_REG6 {
regulator-name = "dcdc6";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3450000>;
regulator-always-on;
};
/* aldo */
ldo_1: LDO_REG1 {
regulator-name = "ldo1";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
regulator-boot-on;
};
ldo_2: LDO_REG2 {
regulator-name = "ldo2";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_3: LDO_REG3 {
regulator-name = "ldo3";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_4: LDO_REG4 {
regulator-name = "ldo4";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
/* dldo */
ldo_5: LDO_REG5 {
regulator-name = "ldo5";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
regulator-boot-on;
};
ldo_6: LDO_REG6 {
regulator-name = "ldo6";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_7: LDO_REG7 {
regulator-name = "ldo7";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_8: LDO_REG8 {
regulator-name = "ldo8";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
regulator-always-on;
};
ldo_9: LDO_REG9 {
regulator-name = "ldo9";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
ldo_10: LDO_REG10 {
regulator-name = "ldo10";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
regulator-always-on;
};
ldo_11: LDO_REG11 {
regulator-name = "ldo11";
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <3400000>;
};
sw_1: SWITCH_REG1 {
regulator-name = "switch1";
};
};
pmic_pinctrl: pinctrl {
compatible = "pmic,pinctrl,spm8821";
gpio-controller;
#gpio-cells = <2>;
spacemit,npins = <6>;
/**
* led_pins: led-pins {
* pins = "PIN3";
* function = "sleep";
* bias-disable = <0>;
* drive-open-drain = <0x1>;
* };
*/
};
pwr_key: key {
compatible = "pmic,pwrkey,spm8821";
};
ext_rtc: rtc {
compatible = "pmic,rtc,spm8821";
};
};
};
在 Linux 内核驱动中使用 regulator 的方法：
1. 配置dts，引用想要使用的regulator
&cpu_0 {
clst0-supply = <&dcdc_1>;
vin-supply-names = "clst0";
};
代码中获得相应的句柄：
const char *strings;
struct regulator *regulator;
err = of_property_read_string_array(cpu_dev->of_node, "vin-supply-names",
&strings, 1);
regulator = devm_regulator_get(cpu_dev, strings); --> 传入的struct device *必须有实体对应
代码中使能相应的regulator:
regulator_enable(regulator);
代码中设置相应的regulator的电压：
regulator_set_voltage(regulator, 95000000, 95000000);